Covering London & Home Counties
Answers / Your walls

Your walls, answered.

Can you render over painted brick?

Yes, if the paint is firmly bonded. We apply a primer and a PRB Renomur or EWI Pro basecoat with mesh straight over the sound paint, then a silicone finish, about 10mm thick in total. Flaking areas are scraped back first, but there is no need to strip the whole wall.

The first check is adhesion. At the survey we score a small cross into the paint, press tape over it and pull it away, and we look for flaking, blistering and areas where damp has pushed the paint off. Firm paint stays, while loose and flaking patches are scraped back and primed so the new layers grip evenly. The build up is roughly 8mm of basecoat with mesh, a primer, then a grain finish of about 1.5mm, which only slightly changes the line of the wall at window reveals and sills. That thin build means downpipes and fittings can usually go back on with longer fixings. If the paint is peeling because of damp, we look for the cause, such as a leaking gutter or a bridged damp proof course, before covering it. A close photo of the paint beside a scraped patch helps us judge it before we visit.

Can you render over pebbledash?

Often, yes. If the pebbledash is firmly bonded, a levelling basecoat with mesh can go straight over it. If it sounds hollow when tapped, or is cracked and loose, it has to be hacked off first. We tap test every elevation at the survey to decide.

Pebbledash fails in two ways. The stones loosen and fall, or the whole coat behind them parts from the brick and sounds hollow. If it is sound, a levelling basecoat with mesh fills the texture and gives a flat base for the finish, which saves a great deal of mess and cost. If it is hollow, we often start with a test patch at a corner, where it is easiest to get behind, to see how well it is bonded. Where removal is needed, a hammer and bolster is slower but kinder to soft brick than a breaker, and any brick face damage is covered by the levelling coat. Pebbledash removal and re render on a semi usually costs £12,000 to £18,000. If insulation is on your list, EWI boards fixed with adhesive and mechanical fixings can go over sound pebbledash without hacking off.

Should old render be removed or rendered over?

If the old render is solid, rendering over it with a meshed basecoat is quicker and cheaper. If it is hollow, cracked through or holding damp, it needs to come off. Many houses end up with a mix: the failing patches removed and the rest overcoated.

The decision is made wall by wall. We tap test the surface for hollow areas, look for cracks that run through to the brick, check for bulging and for damp staining inside the house, and note where earlier patches have been made. Small hollow areas are cut out, primed and filled flush with a levelling coat, then the whole wall is overcoated with a meshed basecoat so old and new areas move together. Where most of a wall is failing, it is usually cheaper overall to take it all off than to patch it again and again. Renewing render over more than half of a wall can trigger the building regulations insulation requirement, so it may make sense to consider EWI at the same time. We mark up each elevation at the survey so you can see what comes off and what stays.

Can you render over existing render?

Yes, when it is sound. We clean the wall, repair cracks, prime, then apply a basecoat with mesh and a new finish. Overcoating avoids the mess and cost of hacking off and gives a uniform new surface.

Overcoating starts with cleaning. Any algae or lichen is treated with a biocide and left for a day or two before a low pressure rinse, and dirt and loose paint are brushed off. Cracks are opened slightly so filler can key in, then filled with a compatible repair material, and hollow patches are cut out and made good. Then comes primer, a basecoat of about 8mm with mesh across the whole wall, and the through coloured finish. Existing beads and sills are checked, because the new face sits slightly further out and may need new beads at the edges and a drip at the base. Overcoating will not cure a cause such as a leaking gutter, a cracked lintel or ground movement, so those are put right first or the crack returns. Make a note of any cracks you have watched grow, as that history helps us diagnose them.

Can you render a 1930s semi?

Yes, it is one of the most common jobs we do. Many 1930s semis have cement render or pebbledash that has cracked or come loose. We either overcoat the sound areas or hack off and re render with a modern meshed system, often adding external wall insulation at the same time.

A typical London 1930s semi has a bay window, a tiled porch and a rendered or pebbledashed upper floor, and many have solid brick walls about 230mm thick. Over the decades, cement render cracks, pebbledash comes loose around the bays, and patch repairs leave a mismatched finish. Lime is rarely needed on these houses, because a breathable modern system suits the brickwork. Where render is failing on a solid wall, the two usual routes are hacking off and applying PRB monocouche, or fitting 90mm Rockwool EWI with PRB render over the existing render, which avoids hacking off and cuts heat loss. Bays need careful detailing, with beads at every angle and meshed corners. Check whether your road sits in a conservation area, as that can affect changes to the front. Send a photo of the front and the rear and we can give you a written quote within 24 hours.

Can you render a Victorian house?

Yes, but the wall decides the system. Victorian walls are usually soft solid brick, so we use breathable systems and protect original details such as cornices and window surrounds. Stucco fronted houses get lime or matching stucco repairs.

Victorian brick is usually soft and laid in lime mortar, so the wall needs to let moisture move in and out. A hard cement render traps that moisture, which shows as blown render, crumbling brick faces and damp inside. On these houses we choose a breathable system, and on very soft or historic walls we use PRB lime products, namely Primchaux PE, Tradi GP and Tradi Lisse. Plain stucco is a smooth sponged lime render, while rebated stucco is cut to look like ashlar blocks, which is slower and dearer. Cornices, window surrounds and string courses can be repaired or run in place, or replaced with ready made EPS profiles that are bonded, meshed and rendered over. Before any work, we check for failed pointing, leaking gutters and bridged damp proof courses. If the house is listed or in a conservation area, consent may be needed before the front changes.

Does render cause damp?

Not when the right system is used. Damp problems come from hard cement render trapping moisture in old solid walls, or from render bridging the damp proof course. We stop render above the damp proof course with a bell cast bead and use breathable systems on solid walls.

Render causes damp when it is the wrong material or badly detailed. Hard cement on soft solid brick holds moisture in the wall, and once it cracks, rain gets behind it and struggles to dry out. Render run down to the ground bridges the damp proof course and lets ground moisture climb into the wall. Missing drip details at sills and copings send water into the joints. We stop the render about 150mm above ground at the damp proof course with a bell cast bead, use breathable systems on solid walls, and fit beads and sills that shed water away from the face. If you already have damp patches, look outside for render that touches the ground, raised paths or flower beds against the wall, and cracks near gutters and downpipes. Those are the usual culprits, and most can be dealt with as part of the re render.

Will rendering fix a damp wall?

Render is not a damp cure. If the damp comes from leaking gutters, high ground levels or failed pointing, fix that first. A new breathable render does stop rain soaking into porous brick, which helps walls that get damp from driving rain.

The first step is finding where the water comes from. Penetrating damp from driving rain usually shows on exposed elevations after storms, and a breathable render helps here because it sheds rain while letting the wall dry. Damp low down often comes from high ground levels, raised paths or render bridging the damp proof course, which needs the ground lowered or the render cut back. Damp around windows or upstairs points to gutters, downpipes, sills or failed pointing. Condensation inside, often in kitchens, bathrooms and bedrooms with poor ventilation, is a separate problem that render alone does not solve. On solid walls, external insulation can raise the inner wall temperature and reduce condensation, which helps where cold walls are the cause. Note where the damp appears, when it gets worse and what the weather was doing, as that tells us more than a damp meter reading alone.

Can you render a solid wall house?

Yes. Solid walls need a breathable system so moisture can escape. Modern silicone and mineral systems let vapour through, and lime is used on very old or soft masonry. Re rendering is also the best moment to consider external wall insulation, because solid walls lose the most heat.

Most Victorian and Edwardian houses in London, and many from the 1930s, have solid brick walls about 230mm thick with no cavity. You can often tell from the brick pattern, where some bricks are laid end on as headers. These walls rely on drying out through their faces, so the render must let vapour pass. Uninsulated, they have a U value of about 2.0 W/m²K, and 90 to 100mm of insulation brings them close to the 0.30 W/m²K target for upgraded walls. If render is renewed over more than half of a wall, or more than a quarter of the whole outer surface, building regulations expect insulation to be improved where practical. Where the existing cement render is failing, the usual choice is to hack off and apply PRB monocouche, or to fit 90mm Rockwool EWI with PRB render over the old render.

Can you render blockwork or a new build?

Yes. Blockwork and new build walls are ideal for monocouche, usually over a basecoat where different materials meet. We keep one PRB specification across the whole building so the manufacturer warranty covers all of it.

New blockwork gives a regular, absorbent background that suits PRB monocouche. Where blockwork meets brick, concrete, timber or steel, the materials move differently, so we add a basecoat with mesh across the junction and diagonal mesh patches at window and door corners. Movement joints designed into the building are carried through the render with suitable beads. Blockwork needs to be dry and the mortar cured before rendering, and work only goes ahead at 5°C and rising, with no frost for 24 hours. On a new build we keep one PRB specification across every elevation, lightwells included, so one warranty covers the whole building. For contractors and architects, it helps to agree bead positions, sill projections and window details before the frames go in, as late changes cost time on site. Share your drawings with us early and we can price the render package from them.

Still deciding?

Tell us about your property.

Send photos of each elevation and we’ll come back with a written quote within 24 hours.

Get a free quote →